| View previous topic :: View next topic |
| Author |
Message |
Rubi
Joined: 11 Feb 2010
Posts: 4
|
 Posted: Thu Feb 11, 2010 1:13 pm Post subject: Osif not recognized |
 |
|
Hi
I built the Osif on a pcb from seeedstudio.
I flashed the bootloader and programmed the firmware.
But when i scan the port, the software does not find the osif.
I allways get found adapters -1
Any ideas ?
Cheers
Rubi |
|
| Back to top |
|
 |
jharvey
co-admin
Joined: 15 Mar 2009
Posts: 350
Location: Maine USA
|
| Posted: Thu Feb 11, 2010 10:05 pm Post subject: |
|
|
| I guess the first things first, when you scan, are you connected to a good openservo board? I think you're referencing the diag software scan. If so that scan will scan the I2C bus looking for OpenServos. |
|
| Back to top |
|
|
Rubi
Joined: 11 Feb 2010
Posts: 4
|
| Posted: Fri Feb 12, 2010 5:32 pm Post subject: |
|
|
Hi
| jharvey wrote: | | I guess the first things first, when you scan, are you connected to a good openservo board? I think you're referencing the diag software scan. If so that scan will scan the I2C bus looking for OpenServos. |
No I just have the adapter in the moment, but shouldn't it appear as adapter while scanning ?
I only get:
"No adapters found, but got this far regardless. Something went horribly wrong."
Cheers
Rubi |
|
| Back to top |
|
|
ginge
Site Admin
Joined: 14 Jan 2006
Posts: 1029
Location: Manchester, UK
|
| Posted: Fri Feb 12, 2010 8:16 pm Post subject: |
|
|
are you windoes or linux?
for linux open a console and type lsusb
You should see OSIF listed as 1964:0001
Did you flash the bootloader on first, or just the main firmware. It sounds like either the firmware is not quite right, or there is a problem with the hex file.
If you want I can upload a basic hex with the working firmware.
_________________
http://www.headfuzz.co.uk/
http://www.robotfuzz.co.uk/ |
|
| Back to top |
|
|
Rubi
Joined: 11 Feb 2010
Posts: 4
|
| Posted: Sat Feb 13, 2010 4:17 pm Post subject: |
|
|
Hi!
Thank you for your help!
| ginge wrote: | | are you windoes or linux? |
I use windows xp.
| ginge wrote: |
Did you flash the bootloader on first, or just the main firmware. It sounds like either the firmware is not quite right, or there is a problem with the hex file. |
Exactly, I installed the bootloader and then used the firmware flash programm.
| ginge wrote: |
If you want I can upload a basic hex with the working firmware. |
I used a file from the repositore, is your firmare different ?
Anyhow, it would be worth to try, thank you!
Cheers
Rubi
Last edited by Rubi on Sun Feb 14, 2010 7:06 am; edited 2 times in total |
|
| Back to top |
|
|
Rubi
Joined: 11 Feb 2010
Posts: 4
|
| Posted: Sat Feb 13, 2010 7:04 pm Post subject: |
|
|
THANK YOU!!!!
Works now, it was the firmware.
So, time to invest in some open servos. 
Cheers
Rubi |
|
| Back to top |
|
|
|
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
